+44 (0)1702 543500
Currency locked: please either change during payment stage or update your account.
Home >  mas >  piezo drivers

MAS6240C2HP06 Low Noise/EMI Piezo Buzzer Driver

Report an error

Part number: MAS6240C2HP06
Outline: QFN-12
Part Status: Active
Product family: mas6240
Pack size: Reel 5k
Datasheet: See below  THAT5171N32-U datasheet
Manufacturer:



Profusion also accepts PayPal

CHANGE CURRENCY:   

?

Quantity:  

QUANTITY 1+ 10+ 50+ 100+ 500+ 1k+
gbp 3.25 2.84 2.43 1.95 1.50 1.35

Available Stock: >1K


For scheduled orders and further information:

Features

  • Integrated Charge Pump generates 18V from 3V supply
  • Single Ended or Differential Output
  • Inductorless Solution
  • Few External Parts Required

Full Description

The MAS6240 is a piezo driver device that can drive outputs up to 18Vpp from a 3V supply. An internal three-mode charge pump generates a boosted supply voltage for the piezo driver. To adjust the piezo element sound volume, the charge pump can operate in either 1x, 2x or 3x mode. In 1x mode the output voltage is the same as the input voltage while in 2x or 3x mode the input voltage is boosted accordingly.

The MAS6240 is an easy and low-cost peizo driver solution since only 4 small value capacitors are needed in addition to the sound element. No inductors are required. This design also causes significantly less disturbance to the surrounding circuits making it an ideal choice for sensitive designs. Its charge pump switches at 1MHz, allowing the use of external capacitors as small as 100nF.

Control logic switches the charge pump on at the first rising signal of the digital input (DIN) pin. The switch-off signal is generated while the signal at DIN has been low for 50ms. The piezo driver is enabled at a second rising edge of a pulse at DIN and the signal is transferred to piezo output VO1. The same signal is inverted into output VO2 for the differential output.

A continuous high logic level at the DIN input causes the charge pump to be turned ON but leaves the audio amplifier disabled. In that state the charge pump output can be used to power the external LEDs or any other external circuit. The output voltage is still selectable in three steps. In "disabled" mode (DIN has been low for 15ms typically) all functional blocks are switched off to achieve a quiescent current of less than 1μA.

Supply Voltage (maximum)3.3VSupply Voltage (minimum)2.2VSupply Current1.5mAQuiescent Current1V-out max18Vfo-max0.008MHzStandbyYes

The above data refers to this component's master part. Please also refer to the Datasheets & Resources tab or visit this part's master part page.

UK Customers

Orders below 100.00 can be delivered by Registered Post at a rate of 3.50 (allow 3-5 days) or a next day tracked courier at a rate of 9.00.
Orders above 100.00 are delivered by a next day tracked courier at a rate of 9.00.


European Customers

Orders below 100.00 can be delivered by Airmail (allow 5-7 days) at a rate of 5.50 or by a tracked courier at a rate of 19.50 (1-2 days).
Orders to European countries above 100.00 are delivered by a tracked courier at a rate of 19.50 (1-2 days).


US Customers

Orders below $110.00 can be delivered by Airmail at a rate of $9.00 (allow up to 10 days) or by tracked courier at a rate of $30.00 (1-3 days).
Orders above $110.00 are delivered by a tracked courier at a rate of $30.00 (1-3 days).


International Customers

Orders below $50.00 can be delivered by post (allowing up to 28 days) at a rate of $18.00 or by a tracked courier at a rate of $49.00.
Orders above $50.00 are delivered by tracked courier at a rate of $49.00.


All prices shown exclude VAT.